It is always a great pleasure to be able to enjoy a good time out on sailing trips , be it for fishing, and some other activities. But before everyone realize it, good times flies and the day turns dawn and into night pretty fast. It’s easy to get caught up stuck out on the water when night arrives, while everyone start to get the urge of needing to get back.

This is when solar dock lights comes in handy ! While other types of lights can ( and do ) brighten up your yacht , most seamen do have a good sense of eco-friendly. Traditional lights would either consume battery ( which contain chemicals ), or power charged lights. Such lights powered by battery and/or electricity would certainly need continual charging in order to keep your yacht light-up. Well….that’s not a good way to be eco-friendly for sure.

One thing for sure is that Solar dock lights don’t have these concerns. Solar lights receive and recharge its power and energy all from the sun. It’s battery gets charged up during the day totally free of cost from the sun , and environment friendly for sure ! Without you realizing it, it is fully charged by dawn when you needs it at night. Fully charged up Solar dock lights could probably last up to 18 hours usage, and the brightness level is even better from conventional lights. This for sure comes handy when you are out to the sea for days, comparing to conventional batter-charged lights which always need replacement.

Further, for safety cautions, when walking on the yacht dock in the night, be sure to have your dock lighting always on which helps to provide clear directions. Thus while you and friends are busy enjoying fun filled water activities, don’t forget to make sure your yacht is well prepared with necessary lighting tools. These solar dock lights are also setup to detect and automatically switched on when the night falls upon while all the guests are still enjoying the fun time.

Choosing the Right Dock Light’s Size and Style
For most, you should be able to find the suitable dock lights that suit your yacht size. For best coverage, it is wise to equip your yacht with several dock lights for better overall lighting need at night. It is always better to have a fun and safe journey while going out for sea sailing trips.

Heavy ground tackle makes for sound sleeping, but when it’s time to weigh anchor, it can be a pain unless you have a windlass to do the heavy lifting. Fortunately for our lower backs, there are windlasses sized to fit any boat and no reason not to have one aboard as an unpaid hand.

When properly installed, a windlass requires minimal maintenance.Here’s what you need to know.

First, rinse the windlass thoroughly after every voyage to wash off the salt, let it dry, and cover it. (Many anchor lockers are now equipped with the quick-connect-type freshwater connections for rinsing.) Use the windlass frequently to keep the innards lubricated; crank it over for a few turns at least every couple of weeks. If the windlass sits idle, the oil will drop off the internal gears, some of which are steel and prone to rust. Since the windlass is ex­posed to lots of salt spray, rain, and dampness from wet anchor rods, unpro­tected steel will soon be rusty steel. While you’re at it, manipulate any movable parts—clutches, brakes, chain stoppers, etc. “Use it or lose it” is applicable to windlasses, ton.

At the beginning of the season, disassemble, clean, and lubricate the windlass according to the directions in the manual. This doesn’t require major surgery, just basic field-snipping that anyone can do. Use the type of grease recommended by the manufacturer, being careful to keep friction clutches and brakes lobe-free. Repeat the process at lay-up or at no less than six-month in­tervals if you use your boat year-round.

Look around the fastenings for signs of leakage, which can lead to water intrusion into cored decks, an expensive and frustrating condition to repair. Check below decks as well, where water drips leave rust stains even on stainless steel fas­tenings. Misuse of the windlass, e.g., using it to absorb the strains of anchoring rather than transferring the rode to a mooring cleat (or nylon snubbed in the case of chain), can overstress the fastenings, break the bedding, and let water in. Don’t ignore leaks.

Inspect all electrical connections for problems. Connections should be clean, corrosion free (corrosion looks like the white deposits you often find on your car’s battery cables), and devoid of burned areas that can result from arcing. If nec­essary, remove the leads (shutoff the power first—there are a lot of amps here), clean the terminals and posts, and re­connect.

Coat the connec­tions with grease, and re-cov­er them with the boots. Look at the motor casing, too; it’s usually painted steel, and if the paint’s nicked, it’ll rust. Touch up the paint be­fore it gets worse.

Also, check the footswitch­es on the foredeck. The hinged caps should open and close easily and have a firm, tight fit for preventing accidental activations. Be­cause the rubber can be damaged by exposure to UV rays, the diaphragms on the switches should be doused with 303 Protectant or another UV shield. The switches can also be silicone-sealed around their edges. Finally, when you use the windlass, don’t make it do all the work. Motor toward the anchor so there’s minimal strain on the rode.

If the anchor doesn’t break out easily, belay the rode and pop it free with the engine, then use the windlass to lift it back aboard. Your windlass will last longer and be happier if you don’t overstress it.

A portable oil-changer is basically a five- gallon plastic bucket with a pump mounted on top; the pump sucks up old lube oil through a cocktail-straw-size tube via the dipstick hole and dumps it into the pail.

I used one of these for a couple of years on my GM-powered Hatteras, and it worked fine, albeit slowly—very slowly. If you’re talking twin engines plus gears, plus a genset, pack a lunch when you change your oil, because you’re going to be there a while.

A better solution is to invest in a built-in oil-change system, comprising a reversible electric pump and a manifold of valves plumbed to your engine crankcases, trans­missions, and genset. You pump the used oil into a container, and then move the exhaust hose into a five-gallon pail of fresh oil (where it now becomes the supply hose), re­verse the pump, and refill. The oil is quickly pumped out and in via the oil pan drain, rather than through the dipstick tube. You’ll also have to find a place to dispose of the old oil properly—ask your marina manager or even your dockmates for their advice.

Reverse, X-Change-R, and Jabsco sell oil- change systems to suit multi-engine setups. Installation is straightforward, but drains each engine before pulling the oil-pan plug, or you’ll have an EPA-size cleanup job. I’d bite the bullet and pay the yard—its mechanics are skinnier.